Kia Soul: Steering Gear box. Replacement - Electric Power Steering - Steering SystemKia Soul: Steering Gear box. Replacement

Kia Soul 2014-2019 PS Service Manual / Steering System / Electric Power Steering / Steering Gear box. Replacement

1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Loosen the bolt and then disconnect the universal joint assembly (A) from the pinion of the steering gear box.
Tightening torque :
32.4 ~ 37.3N.m (3.3 ~ 3.8kgf.m, 23.9 ~ 27.5lb-ft)

  
• Do not use the bolt again.
3.
Remove the front wheel and tire (A) from front hub.
Tightening torque :
88.2 ~ 107.8N.m (9.0 ~ 11.0kgf.m, 65.0 ~ 79.5lb-ft)

  
Be careful not to damage to the hub bolts when removing the front wheel and tire (A).
4.
Remove the stabilizer link (A) loosening the nut.
Tightening torque :
98.1 ~ 117.7N.m(10.0 ~ 12.0kgf.m, 72.3~86.8lb-ft)

5.
Remove the tie rod end ball joint (C) from the knuckle by using the SST (09568-34000).
(1)
Remove the split pin (A).
(2)
Remove the castle nut (B).
(3)
Use the SST (09568-34000).
Tightening torque :
23.5 ~ 33.3N.m(2.4 ~ 3.4kgf.m, 17.4 ~ 24.6lb-ft)

  
•
When using SST, be sure not to damage the dust cover of lower arm ball joint.
•
Keep SST tied to the car because there is a risk of injury by dropping the SST during removing the lower arm ball joint.
•
The peripheral parts may be damaged when removing the lower arm ball joint with a general tool such as lever, so be sure to use SST.
6.
Loosen the bolt & nut and then remove the lower arm (A).
Tightening torque :
58.9 ~ 70.6 N.m (6.0 ~ 7.2 kgf.m, 43.4 ~ 52.1 lb-ft)

7.
Loosen the bolt and then separate the roll rod stopper (A).
Tightening torque :
107.9 ~127.5N.m(11.0 ~ 13.0kgf.m, 79.6 ~ 94.0lb-ft)

8.
Disconnect the muffler rubber hanger (A).
9.
Loosen the bolts & nuts and then remove the sub frame (A).
Tightening torque :
Sub frame mounting bolt & nut
156.9 ~ 176.5N.m(16.0 ~ 18.0kgf.m, 115.7 ~ 130.2lb-ft)

10.
Remove the heat protector (A).
Tightening torque :
6.9 ~ 10.8N.m(0.7 ~ 1.1kgf.m, 5.1 ~ 7.9lb-ft)

11.
Remove the stabilizer (A) from the front sub frame by loosening the mounting bolts & nuts.
Tightening torque :
44.1 ~ 53.9N.m(4.5 ~ 5.5kgf.m, 32.5 ~ 39.8lb-ft)

12.
Remove the gear box (A) from the front sub frame by loosening the mounting bolts.
Tightening torque :
88.3 ~ 107.9N.m (9.0 ~ 11.0kgf.m, 43.4 ~ 57.9lb-ft)

13.
Installation is the reverse of removal.
  
•
Must be ASP calibration and EPS type recognition after assembling.
14.
Check the wheel Alignment.
(Refer to Suspension System - "Alignment")
    Steering Gear box. Components
    1. Steering Gear box ...

    Steering wheel
    ...

    See also:

    Air Conditioning refrigerant label
    Each symbols and specification on air conditioning refrigerant label means as below ; 1. Classification of refrigerant 2. Amount of refrigerant 3. Classification of Compressor lubricant Refe ...

    Description of ESC
    Electronic Stability Control (ESC) recognizes critical driving conditions, such as panic reactions in dangerous situations, and stabilizes the vehicle by wheel-individual braking and engine c ...

    Components
    1. Clutch pedal assembly 2. Ignition lock and clutch switch 3. Master cylinder 4. Clutch tube 5. Clutch release cylinder ...