Kia Soul: Rear Seat Back Cover Replacement
[LH] |
|
|
1. |
Remove the rear seat back assembly [LH].
(Refer to Rear Seat - "Rear Seat Assembly")
|
2. |
Push the lock pin (B), remove the rear seat headrest (A).
|
3. |
Remove the lock hook (B) and then remove the rear seat armrest
(A).
|
4. |
Press the rear seat armrest (A) in the direction of the arrow
in the below picture, and then remove it by pulling it up.
|
5. |
Using a screwdriver or remover, remove the rear seat folding bezel
(A).
|
6. |
Using a screwdriver or remover, remove the rear seat belt center
cover (A).
|
7. |
Using a screwdriver or remover, remove the tether anchor ganish
(A).
|
8. |
Using a screwdriver or remover, remove the rear seat back bush
hinge (A).
|
9. |
Remove the protector (A) located in the bottom side of the rear
seat back.
|
10. |
Zip off the rear seat back cover located in the side (A), and
then pull it up.
|
11. |
Pull out the hooks (A) by the rear seat back frame.
|
12. |
Turn the rear seat back cover inside out. Then pull out the headrest
guides (A) while pinching both sides of the lower part of the guides,
and remove them.
|
13. |
Remove the rear seat back cover (A) from the rear seat back frame
(B).
|
14. |
After removing the hog-ring clips (A) on the rear of seat back
and remove the rear seat back cover (B).
|
15. |
Install in the reverse order of removal.
|
[RH] |
|
|
1. |
Remove the rear seat back assembly [RH].
(Refer to Rear Seat - "Rear Seat Assembly")
|
2. |
Push the lock pin (B), remove the rear seat headrest (A).
|
3. |
Using a screwdriver or remover, remove the rear seat folding bezel
(A).
|
4. |
Using a screwdriver or remover, remove the tether anchor ganish
(A).
|
5. |
Using a screwdriver or remover, remove the rear seat back bush
hinge (A).
|
6. |
Remove the protector (A) located in the bottom side of the rear
seat back.
|
7. |
Zip off the rear seat back cover located in the side (A), and
then pull it up.
|
8. |
Pull out the hook (A) by the rear seat back frame.
|
9. |
Turn the rear seat back cover inside out. Then pull out the headrest
guides (A) while pinching both sides of the lower part of the guides,
and remove them.
|
10. |
Remove the rear seat back cover (A) from the rear seat back frame
(B).
|
11. |
After removing the hog-ring clips (A) on the rear of seat back
and remove the rear seat back cover (B).
|
12. |
Install in the reverse order of removal.
|
Rear Seat Back Cover Component Location
1. Rear seat back cover [LH] 2. Rear seat back cover [RH] ...Rear Seat Cushion Cover Component Location
1. Rear seat cushion cover ...See also:
Ignition Coil Removal
1.
Disconnect the battery nagative terminal.
2.
Remove the engine cover.
3.
Disconnect the ignition coil connec ...
GVWR (Gross vehicle weight rating)
This is the maximum allowable weight of the fully loaded vehicle (including all
options, equipment, passengers and cargo). The GVWR is shown on the certification
label located on the driver’s do ...
Tightening Torque
Items
N.m
Kgf.m
lb-ft
Front and rear doors
Door hinge to body
34.2 ~ 41.2
3.5 ~ 4.2
25.3 ~ 30.4
Door hinge to door
...